1、EN 61347-1 附錄A1,A2,A3怎么測量？
2、什么是SELV等效控制器？--By Melodymg
3、現CB認證的關鍵元器件清單中，很多工程師用IEC的標準，這樣可以？
4、等離子燈具中，射頻驅動模塊需要做測試嗎？或者需要有認證碼？--By Yangcanluck
5、EN 61347-2-13中的Tc怎么找到？是不是表面每個位置的溫度都要測試過，找到溫度最高的地方？--By Faige 2006
6、我司有一款臺燈，做UL 153，只有一根電源線加裝飾性的燈座。現在的問題是：因燈座沒有與燈架充分固定，在旋轉燈座時，電源線就會被隨著扭轉，電源線扭轉會超過360度，有沒有標準條款可以免除固定燈座的要求？--By Kaiden
7、IEC/EN60598-1,60968中，輸入?yún)?shù)怎么確認？例如：客戶標稱100W,實際在額定電壓下只有60W，是否OK？
8、EN62031中過功率測試方法是怎樣的？--By arbi、Liyun_01
9、IEC/EN 61347-2-13中，SELV-equivalent是否已經取消？
10、IEC/EN 61347-2-13中，接線端子是否需要評估60598中的8mm要求？
11、UL 1310+UL 8750的電源是否要求Class I電源的次級到地需要有Y-cap？--By浪子邊城
12、UL 1993+UL 8750對自鎮流球泡燈包裝要求（即標示）？
13、UL 1993+UL 8750膠水老化測試要求？--By Ivy Chen
14、什么是general coverage？是專指免溫升測試嗎？
15、關于LED 臺燈等燈具，可以適用general coverage嗎？--By 無名氏
16、EN 61347電源驅動產品只有壓線口沒有提供電源線，是否還要做60598的電源線拉力測試？--By 環日邊
17、12V MR16做CE是否一定要用Fuse？
18、保險電阻會被限制使用嗎？
19、燈具做CE，對Fuse有什么要求？--By halphine
20、UL 1598中，天花燈，櫥柜燈做溫升測試時的設備是什么樣子的？--By elaincle
21、戶外景觀LED燈，驅動電源板是否可以直接裝在金屬外殼內?非隔離式電源是否可以先裝在塑膠管內再裝入金屬外殼？--By yyh
22、哪些國家適用什么樣的燈頭可以從哪個標準上看到？--By 50366A1
23、溫升測試在常溫下測還是40度下測試？
24、溫升測試對于沒有標出限值的器件怎么樣判定是否合格？例如：電源里的開關IC、三極管、功率電阻等。
25、短路測試需要短路哪些器件？
26、爬電距離和電氣間隙不足，是否短路測試沒有安全隱患就能判定合格？--By Reliab
27、外殼為玻璃的球泡燈，輸出非SELV，這樣的結構能否接受？
28、IEC 60598-2-20中對燈串marking的要求？
29、LED軟條燈測試標準可用EN60598-2-4或EN60598-2-20嗎？--By Ivy Chen
30、IEC60598-1中溫升測試的環境溫度是多少？25度還是規定的Ta（Max）？--By edwardguo 001
31、IEC61347標準中，怎樣區分獨立式鎮流器和內置式鎮流器？--By Shalu 2
32、鎮流器內部灌膠后，因?yàn)榻^緣要求已經達到，可否不考慮爬電距離個電氣間隙的要求？--By jing 005213
33、EN標準和IEC標準的區別？EN 和IEC 標準偏差在哪里可以看到？
34、CB和LVD都指安全，他們的區別是什么？
35、GS和CE能等同嗎？還是要加上EMC？
36、Erp以及2013年1月2日Rohs的宣告？
37、是不是IT產品上所有的指示燈要做62471，Laser做60825？--By DavidFu，無名氏
38、LED路燈工作溫度定義為-40°--60°，驅動電源是內置的，做溫升時是以Ta值考量還是以Tc值做考量？
39、外置式獨立電源Ta與Tc的關系？
40、LED路燈要求IP等級大于IP65，如果能達到IP67，在標簽上是否都要寫IP67，IP65？
41、LED路燈的整體是達到IP65，如果是內置式電源，電源的防水等級如何考量？
42、LED路燈要求承受風力測試，在認證機構測試時，是以實際安裝角度來模擬測試還是認證機構自己定義？--By Babyliss
43、LED燈管做UL的標準有UL1993，UL8750，UL1598 ，是否出現標準重復？--By Kevin528
44、怎樣才能滿足UL2097？--By San zhu

 
6、我司有一款臺燈，做UL 153，只有一根電源線加裝飾性的燈座。現在的問題是：因燈座沒有與燈架充分固定，在旋轉燈座時，電源線就會被隨著扭轉，電源線扭轉會超過360度，有沒有標準條款可以免除固定燈座的要求？--By Kaiden

答復：
8.4 When wires pass through a joint between sections of a portable luminaire that are separable for packing purposes, the joint shall be such that rotation of one section with respect to the other during the assembly of the sections is limited to not more that 360 degrees. Friction alone does not meet the intent of the requirement to prevent rotation.
Exception: When all of the following conditions exist, rotation between sections of a portable luminaire is not limited to 360 degrees:
a) The internal diameter of the tubing through which the wires pass is 1/2 inch (12.7 mm) or more or the Power Supply Cord Twist Test, Section 135A is conducted with acceptable results; and
b) The rotation during assembly is limited to not more than one revolution for each 3 inches (76 mm) of unobstructed tubing length through which the wires pass, when such rotation does not place any stress on the conductors; and
c) The conductors do not involve splices unless the splices are:
1) Inaccessible during assembly in accordance with Accessibility of Live Parts, Section 23; and
2) Secured and provided with strain relief that has been shown to be reliable and not easily defeated by the user.

11、UL 1310+UL 8750的電源是否要求Class I電源的次級到地需要有Y-cap？--By浪子邊城
請看標準：
UL1310:

12.2 There shall be no components connected between primary and output circuits which result in a conductive connection (see 5.4). If capacitive coupling is provided between primary and output circuits, it shall consist of either:

a) A capacitor complying with the antenna coupling requirements specified in the Standard for Capacitors and Suppressors for Radio- and Television-Type Appliances, UL 1414; or

b) Two capacitors connected in series, each capacitor complying with the requirements in 34.1.3.

UL8750:

7.9.2 A component that bridges two circuits otherwise required to be isolated from one another shall be one of the following:

a) A capacitor complying with the antenna coupling requirements specified in the Standard for Capacitors and Suppressors for Radio- and Television-Type Appliances, UL 1414,

b) Two capacitors connected in series, each capacitor individually complying with the dielectric voltage withstand test of 8.4,

c) An optical isolator complying with the requirements of the Standard for Optical Isolators, UL 1577, with a suitable isolation voltage rating, or

d) Isolation provided by a transformer that complies with the dielectric voltage withstand test of 8.4.

 

12、UL 1993+UL 8750對自鎮流球泡燈包裝要求（即標示）？
必須看標準，看結構， 不羅列。
13、UL 1993+UL 8750膠水老化測試要求？--By Ivy Chen
UL8750
6.7 Potting compound
6.7.1 Potting compound shall not leak, drip, or be released from a unit during any test conducted in accordance with this standard.
6.7.2 During the Temperature Test of 8.3, a potting compound shall comply with (a) or (b) as applicable:
a) A polymeric potting compound shall not exceed its Relative Thermal Index (RTI).
b) An asphalt potting compound shall remain at least 15°C (27°F) below its softening point as determined by the Standard Test Methods for Softening Point of Resins Derived from Naval Stores by Ring-and-Ball Apparatus, ASTM E28.

UL1993:
6.7.7 In the United States, when applying the requirements specified in UL 840 to determine environmental pollution, the device may be evaluated with different environmental pollution degrees. The following conditions apply:
a) A device marked for wet use shall be exposed to environmental pollution degree 3.
b) A device intended for dry or damp locations shall be exposed to environmental pollution degree 2.
c) The portion of a printed wiring board covered with a potting compound or a conformal coating that complies with the requirements in conformal-coating tests described in UL 746C shall be exposed to environmental pollution degree 1.
6.7.8 In Canada, printed circuit boards covered with potting compound or a conformal coating shall comply with the requirements of Annex E.

20、UL 1598中，天花燈，櫥柜燈做溫升測試時的設備是什么樣子的？--By elaincle
參考標準Clause 19.3～19.6.
43、LED燈管做UL的標準有UL1993，UL8750，UL1598 ，是否出現標準重復？--By Kevin528
回復：有重疊也各有側重，各自均有考核重點。